[email protected]

15 Common Applications for Versatile 4140 Steel - Otai

AISI 4140 steel grade is a versatile steel grade. You have 15 different application for 4140 steel here. Check for all applications for 4140 steel. 4140HW Alloy Steel Technical Data4140HW Alloy Steel Technical Data 4140HW meets AISI4140 standards and has improved hardenability and strength in heavier cross-sections. Alloy Description TimkenSteels 4140HW grade is a fine-grained, low-alloy steel that offers optimum heat-treat response in heavier cross-sections. You find 4140HW in a

42CrMo4 Alloy Steel 42CrMo4 Forging 42CrMo4 Flat

42CrMo4 Alloy Steel SAE-AISI 4140 is classified as low alloy steel. Medium carbon steels are high-strength steels that include EN19 as an important member in the low alloy category. These steels show a positive response to a variety of heat treatments. 42CrMo4 is a 1% chromium molybdenum medium hardenability general purpose high tensile steel generally supplied hardened and tempered in the tensile range of 850 1000 Mpa (condition T). 42CrMo4 Alloy steel AISI 4140 42CrMo4 1.7225 SCM440 - Waldun SteelProject Description. AISI 4140 steel Manufacturer and Exporter,supplied with round,square,flat,block,and shaft etc. AISI 4140 is defined as a low alloy steel which has 1% Cr-Mo as strengthening alloy elements.Compared with AISI 4130, it has a higher carbon content with good balance of strength, toughness ,abrasion and impact resistance and heat treatment capabilities,but poor in weldability AISI 4140 Alloy Steel - West Yorkshire SteelForging Preheat the steel carefully, then raise the temperature to 1150-1200°C for forging. Do not forge below 850°C. Annealing Heat the AISI 4140 slowly to 800-850°C and allow enough time for the steel to be thoroughly heated.

AISI 4140 Alloy Steel 1.7225 SCM440 42CrMo4

6. 4140 alloy steel Heat treatment. Annealing AISI 4140 alloy steel is annealed at 872°C (1600°F) followed by slowly cooling in the furnace. Tempering AISI 4140 alloy steel can be tempered at 205 to 649°C (400 to 1200°F) depending upon the desired hardness level. The hardness of the steel can be increased if it has lower tempering temperature. AISI 4140 PipesA519 AISI 4140 Pipes - Prosaic SteelAISI 4140 alloy steel is heated at 845°C (1550°F) followed by quenching in oil. Before hardening, it can be normalized by heating at 913°C (1675°F) for a long period of time followed by air cooling. Forging A519 4140 Alloy Steel Seamless Pipe and Tubes AISI 4140 alloy steel is forged at Datasheet for Steel Grades Carbon Steel AISI 4145Plates / Sheets Plates / Sheets 0.08-200mm(T)*W*L Forging, hot rolling and cold rolling Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting Steel Bar Round Bar, Flat Bar, Square Bar 8-1200mm*L Forging, hot rolling and cold rolling, Cast Black, Rough Turning, Shot Blasting, Coil / Strip Steel Coil /Steel Strip 0.03-16.0x1200mm Cold

Forged 4140 Steel Material Properties

ASTM 4140 Steel 1.7225 - Dongguan OTAI Special Steel Co. Forging of ASTM 4140 Oil and Gas industry Steel material metal Forging of 4140 steel should be carried out between 2200 and 1650 º F (1200 and 900 º C). The lower the finishing temperature from forging, the finer will be the grain size. Forged Steel Rings factory, Buy good price Forged Steel 42CrMo4 SCM440 AISI 4140 Quenching Forged Steel Shafts. Forged Steel Block. S45C CK45 ISO9001 Zinc Plated Forged Steel Bar Stock. Open Die Forging 20CrNiMo AISI4140 Square Plate Steel. Open Die Forging Steel 60tons A105 SAE4140 Flat Bar Plate. ISO9001 SS201 SS304 500mm Die Bright Steel Bar. Forged Steel ProductsAISI 4140 steel 1.7225 42CrMo4 SCM440 - OTAI Special Forging of 4140 steel should be carried out between 2200 and 1650 º F (1200 and 900 º C). The lower the finishing temperature from forging, the finer will be the grain size. This alloy steel should ideally not be forged below 1650 º F (900 º C) and should be slow cooled after forging in Oil or water. 7.